Kinter (K International, Inc.) - Ladderless "C" Channel Cleat Wall Banner Hanger

Are you looking to hang large vinyl, sewn/hemmed banner type signs directly from walls? If so, we have the solution! This ingenious two piece, interlocking wedge-shaped banner hanger assembly makes it safe and simple to display and change out banners of almost any size directly from walls. Each assembly consists of one wall mount track and one banner hanger piece - both sold separately. Also requires our Plastic Banner Dowel Rod (sold separately) to display sewn/hemmed fabric or vinyl banners for a clean finished appearance. "C" channel bottom section also accepts various sign hanging options, such as plastic block end hooks or our line of ladderless clips. Simply prep the wall by screwing the wall mount track piece to the wall (mounting hardware included) and then fasten the "C" channel hanger piece onto the top edge of the banner and gravity does the rest. Signs hang approximately 1 inch offset from wall which creates a handsome dimensional effect. Removable and reusable - all safely from floor level. For use from ground level with our K-Stick® Ladderless Poles. Warning: Not recommended for outdoor use. Wall mount track must be firmly attached to wall. Patented.

Wall mount track and "C" channel banner hanger piece are each sold separately
Wall mount track has holes at 16" on center and comes with toggle screw anchors, stud screws and an instruction sheet
Pre-drilling of holes for wall mount track is required (drill bit sold separately)
Wall mount track piece is 3" tall x 1" wide
"C" channel banner hanger piece accepts our line of Plastic Banner Dowel Rods (sold separately)
"C" channel banner hanger piece is 1-3/4" tall x 2-1/4" wide
Custom colors and lengths available
White PVC material
* For larger, heavier signs over 5 pounds it is possible to have two or more individuals, each with a K-Stick®, raise or lower simultaneously.

Request Information

Unit of Measure

Items	220641 24" Length Ladderless Cleat Wall Mount Track Hanger Request Quote	220642 36" Length Ladderless Cleat Wall Mount Track Hanger Request Quote	220643 48" Length Ladderless Cleat Wall Mount Track Hanger Request Quote	220645 72" Length Ladderless Cleat Wall Mount Track Hanger Request Quote	220668 24" Length Ladderless "C" Channel Cleat Wall Banner Hanger Request Quote
Description	N/A Are you looking to mount large signs directly to walls? If so, we have the solution! This ingenious two piece, interlocking wedge-shaped banner hanger assembly makes it safe and simple to display and change out signs of almost any size directly from walls. Each assembly consists of one wall mount track and one binder banner hanger piece - both sold separately. Simply prep the wall by screwing the wall mount track piece to the wall (mounting hardware included) and then fasten the binder banner hanger piece onto the top edge of the sign (barrel bolt and screw fastening hardware included) and gravity does the rest. Signs hang approximately 1 inch offset from wall which, when combined at the bottom of the sign with our #150675 Square Foam Blocks, creates a handsome dimensional effect. Removable and reusable - all safely from floor level. For use from ground level with our K-Stick™ Ladderless Poles. Warning: Not recommended for outdoor use. Wall mount track must be firmly attached to wall. Male and female barrel bolt fastening hardware must be fully screwed together. Patented Wall mount track and binder banner hanger piece are each sold separately Wall mount track has holes at 16" on center and comes with toggle screw anchors, stud screws and an instruction sheet Pre-drilling of holes for wall mount track is required (drill bit sold separately) Wall mount track piece is 3" tall x 1" wide Custom colors and lengths available White PVC material * For larger, heavier signs over 5 pounds it is possible to have two or more individuals, each with a K-Stick™, raise or lower simultaneously.	N/A Are you looking to mount large signs directly to walls? If so, we have the solution! This ingenious two piece, interlocking wedge-shaped banner hanger assembly makes it safe and simple to display and change out signs of almost any size directly from walls. Each assembly consists of one wall mount track and one binder banner hanger piece - both sold separately. Simply prep the wall by screwing the wall mount track piece to the wall (mounting hardware included) and then fasten the binder banner hanger piece onto the top edge of the sign (barrel bolt and screw fastening hardware included) and gravity does the rest. Signs hang approximately 1 inch offset from wall which, when combined at the bottom of the sign with our #150675 Square Foam Blocks, creates a handsome dimensional effect. Removable and reusable - all safely from floor level. For use from ground level with our K-Stick™ Ladderless Poles. Warning: Not recommended for outdoor use. Wall mount track must be firmly attached to wall. Male and female barrel bolt fastening hardware must be fully screwed together. Patented Wall mount track and binder banner hanger piece are each sold separately Wall mount track has holes at 16" on center and comes with toggle screw anchors, stud screws and an instruction sheet Pre-drilling of holes for wall mount track is required (drill bit sold separately) Wall mount track piece is 3" tall x 1" wide Custom colors and lengths available White PVC material * For larger, heavier signs over 5 pounds it is possible to have two or more individuals, each with a K-Stick™, raise or lower simultaneously.	N/A Are you looking to mount large signs directly to walls? If so, we have the solution! This ingenious two piece, interlocking wedge-shaped banner hanger assembly makes it safe and simple to display and change out signs of almost any size directly from walls. Each assembly consists of one wall mount track and one binder banner hanger piece - both sold separately. Simply prep the wall by screwing the wall mount track piece to the wall (mounting hardware included) and then fasten the binder banner hanger piece onto the top edge of the sign (barrel bolt and screw fastening hardware included) and gravity does the rest. Signs hang approximately 1 inch offset from wall which, when combined at the bottom of the sign with our #150675 Square Foam Blocks, creates a handsome dimensional effect. Removable and reusable - all safely from floor level. For use from ground level with our K-Stick™ Ladderless Poles. Warning: Not recommended for outdoor use. Wall mount track must be firmly attached to wall. Male and female barrel bolt fastening hardware must be fully screwed together. Patented Wall mount track and binder banner hanger piece are each sold separately Wall mount track has holes at 16" on center and comes with toggle screw anchors, stud screws and an instruction sheet Pre-drilling of holes for wall mount track is required (drill bit sold separately) Wall mount track piece is 3" tall x 1" wide Custom colors and lengths available White PVC material * For larger, heavier signs over 5 pounds it is possible to have two or more individuals, each with a K-Stick™, raise or lower simultaneously.	N/A Are you looking to mount large signs directly to walls? If so, we have the solution! This ingenious two piece, interlocking wedge-shaped banner hanger assembly makes it safe and simple to display and change out signs of almost any size directly from walls. Each assembly consists of one wall mount track and one binder banner hanger piece - both sold separately. Simply prep the wall by screwing the wall mount track piece to the wall (mounting hardware included) and then fasten the binder banner hanger piece onto the top edge of the sign (barrel bolt and screw fastening hardware included) and gravity does the rest. Signs hang approximately 1 inch offset from wall which, when combined at the bottom of the sign with our #150675 Square Foam Blocks, creates a handsome dimensional effect. Removable and reusable - all safely from floor level. For use from ground level with our K-Stick™ Ladderless Poles. Warning: Not recommended for outdoor use. Wall mount track must be firmly attached to wall. Male and female barrel bolt fastening hardware must be fully screwed together. Patented Wall mount track and binder banner hanger piece are each sold separately Wall mount track has holes at 16" on center and comes with toggle screw anchors, stud screws and an instruction sheet Pre-drilling of holes for wall mount track is required (drill bit sold separately) Wall mount track piece is 3" tall x 1" wide Custom colors and lengths available White PVC material * For larger, heavier signs over 5 pounds it is possible to have two or more individuals, each with a K-Stick™, raise or lower simultaneously.	N/A Are you looking to hang large vinyl, sewn/hemmed banner type signs directly from walls? If so, we have the solution! This ingenious two piece, interlocking wedge-shaped banner hanger assembly makes it safe and simple to display and change out banners of almost any size directly from walls. Each assembly consists of one wall mount track and one banner hanger piece - both sold separately. Also requires our Plastic Banner Dowel Rod (sold separately) to display sewn/hemmed fabric or vinyl banners for a clean finished appearance. "C" channel bottom section also accepts various sign hanging options, such as plastic block end hooks or our line of ladderless clips. Simply prep the wall by screwing the wall mount track piece to the wall (mounting hardware included) and then fasten the "C" channel hanger piece onto the top edge of the banner and gravity does the rest. Signs hang approximately 1 inch offset from wall which creates a handsome dimensional effect. Removable and reusable - all safely from floor level. For use from ground level with our K-Stick® Ladderless Poles. Warning: Not recommended for outdoor use. Wall mount track must be firmly attached to wall. Patented. Wall mount track and "C" channel banner hanger piece are each sold separately Wall mount track has holes at 16" on center and comes with toggle screw anchors, stud screws and an instruction sheet Pre-drilling of holes for wall mount track is required (drill bit sold separately) Wall mount track piece is 3" tall x 1" wide "C" channel banner hanger piece accepts our line of Plastic Banner Dowel Rods (sold separately) "C" channel banner hanger piece is 1-3/4" tall x 2-1/4" wide Custom colors and lengths available White PVC material
Length	N/A 24"	N/A 36"	N/A 48"	N/A 72"	N/A 24"
Assembly Type	N/A Wall Mount Track	N/A Wall Mount Track	N/A Wall Mount Track	N/A Wall Mount Track	N/A "C" Channel Banner Hanger
Safe Working Load Limit*	N/A 5 lb
Approximate Sign Offset from Wall	N/A	N/A	N/A	N/A	N/A 1"
Wall Mount Track Height	N/A	N/A	N/A	N/A	N/A 1-3/4"
Wall Mount Track Width	N/A	N/A	N/A	N/A	N/A 2-1/4"
Material	N/A Polyvinyl Chloride (PVC)
Color	N/A White
Note	N/A * For larger, heavier signs over 5 pounds it is possible to have two or more individuals, each with a K-Stick™, raise or lower simultaneously.	N/A * For larger, heavier signs over 5 pounds it is possible to have two or more individuals, each with a K-Stick™, raise or lower simultaneously.	N/A * For larger, heavier signs over 5 pounds it is possible to have two or more individuals, each with a K-Stick™, raise or lower simultaneously.	N/A * For larger, heavier signs over 5 pounds it is possible to have two or more individuals, each with a K-Stick™, raise or lower simultaneously.	N/A * For larger, heavier signs over 5 pounds it is possible to have two or more individuals, each with a K-Stick®, raise or lower simultaneously.